Yeedi Vac Hybrid Robot Vacuum Cleaner 2022: Transitional Model To The Next Generation With Cleaning Station. Most recently, the Yeedi company released its new product and judging by the equipment, they set their sights on a serious update and introduction of self-cleaning stations into their gadgets. The Yeedi vac hybrid robot vacuum cleaner is a transitional model that has a special compartment for dumping accumulated debris in a container. The software has been updated and adapted for this function, and for expansion you just need to buy a garbage collection station. The Yeedi vac hybrid has improved surface cleaning capabilities and a larger container when compared to the previous Yeedi vac hybrid model. In the future, a combined model with this device may appear in the kit.
Buy Yeedi Vac Hybrid Robot Vacuum Cleaner
Indeed, the progenitor of the updated model was the Yeedi 2 hybrid, but with more advanced features, such as an enlarged container for collecting garbage, determining and increasing the suction power when cleaning carpets and, most importantly, perhaps the ability to dump garbage at a self-cleaning station.
Specifications
As mentioned above, the characteristics have changed, but slightly and basically it is a slightly enlarged container for garbage collection.
- power (W): 40 W;
- voltage (V): 100-240 V;
- case size: 350 * 350 * 77 (mm);
- filter: HEPA;
- operating time from a full battery charge: up to 110 minutes;
- Built-in battery capacity: 2600 mAh Li-ion;
- Garbage container capacity: 450 ml;
- Wet cleaning container capacity: 240ml;
Packaging and equipment
The delivery set does not include spare parts for consumables, although they are always in abundance in the official store of the seller and for any model.
- Yeedi vac Hybrid vacuum cleaner;
- charging docking station;
- charge station power wire;
- brush / knife for cleaning the elements of the vacuum cleaner;
- microfiber cloth for wet cleaning;
- plastic pad for wet cleaning;
- 1 side brush.
Packing in a cardboard shipping box with an additional cardboard seal. In principle, such protection should withstand a fairly severe impact and protect the contents.
The charging station is similar to the previous model. I felt the convenience during use, since the power wire is located at an angle and there is the possibility of winding it on special ears. It turns out that the wire does not stick out for its entire length. Euro plug for 2.4 A, although the wire used is 0.75mm2. The length is about 1.5 meters, so the location of the charging station is quite convenient and is not tied to a power source.
The station itself is made of black plastic with gloss inserts. It looks attractive and compact. For charging, 2 spring-loaded contacts are used on a horizontal platform. The move is moderate. On the side of the installation, there is a layer of soft sticky rubber on the floor. Protected sticker during transport. Before installing, I recommend that you first try on where the base will stand and whether the vacuum cleaner will find it, and then install it.
Brush for cleaning and cutting hair. A must-have tool if you live with long-haired animals. The brush is hidden under the hinged cover and will never get lost. But it seemed to me that the brush is too small to hold in my hand.
Single piece of wet cleaning cloth. The outer fabric is made of microfiber, and the napkin itself fits comfortably on the plastic pad. Convenience has been retained from the previous model, since during installation the front part completely covers the pad and during cleaning does not fall off when moving over obstacles. Installation on the bottom of the vacuum cleaner with plastic clips. In one of such a latch there is a magnet that makes it clear to the robot about the installed napkin. Without this pad, wet cleaning simply cannot be started.
There is only one side brush and this is a message to the top models of other manufacturers. If you look at it in more detail, you can see the directionality of the bristles, as well as the color and model. For convenience, the left and right brushes differ in color: red and green. This should be taken into account when replacing consumables.
The instruction is in English. And here is a quick guide to setting up, unfortunately, only in English, but the connection is easy to handle. Since the mobile application is still in English and all the steps for setting up and connecting are duplicated with pictures. The manual contains basic skills for maintenance and error correction. Although even errors are highlighted in the application with options for correcting them.
Appearance
The appearance of the vacuum cleaner does not differ from the previous model, but has undergone a number of changes that are visible only on the lower part of the vacuum cleaner. The dimensions are quite compact, especially in height, since 77 mm is a rather low profile, so cleaning under the furniture will not create problems, especially with the absence of protruding parts in the form of lidars.
On the upper part there is a start button for automatic cleaning and a camera peephole. The latter is used for navigation during cleaning and for identification in the mobile control application. Nearby, under the massive hinged cover, there is a switch, a reset button, a container for dry waste, a brush, a reset button and an LED indicator. In fact, the top button has an LED indicator for the mode of operation, illuminated in white or red, indicating an error. And the indicator under the lid is designed to bind to a smartphone and notify about connecting to the network. There is also a sticker with a QR code for secondary identification.
The container can be conveniently removed by the movable handle, and when installed it locks it. The container received small changes compared to the previous model and it is not only an increased size, but also small 2 holes located in the lower part and closed with plastic lids. The covers are designed for dumping debris into the receiving and charging station. Accordingly, in the lower part of the vacuum cleaner there are holes located at the same level. The container itself is equipped with a 3-level filter, a protective cover for the inlet and a convenient hinged cover for dumping debris from the container itself.
Before commissioning, it is imperative to remove the soft stops holding the movable bumper, otherwise the robot will not work correctly. The front of the device has a movable bumper responsible for obstacle detection. Sensitive proximity sensors are installed inside the bumper.
On the opposite side of the movable bumper there is a water container. It is made of transparent plastic, so the control of the remaining water is always visible. Refilling is carried out at the top and is protected by a rubber plug. Water does not spontaneously flow out, it is supplied through a special pump when the wet cleaning mode is on.
The vacuum cleaner has a counterpart for receiving water and supplying it through special holes located on the bottom of the body. The wet wipe is placed directly on the wet wipe container and removed with it. Of course, it is better to remove it directly from the removed container, because the plugs are very tight.
On the lower part of the robot vacuum cleaner, there are 6 fall sensors, 2 wheels with aggressive tread, a drive wheel, charge contacts, a sensor of passage over carpets and a receiving hole for debris. The manufacturer’s label is located by the water container.
Let’s start with the break sensors. There are as many as 6 of them and they are located almost around the entire circumference, which is very good as it protects against falling even when reversing when an obstacle is detected. The sensors are slightly recessed in the housing to prevent damage and contamination.
Wheels with aggressive tread and very long suspension travel. This achieves the best overcoming of obstacles in the form of sills.
Inlet opening with a turbo brush and a suspension mechanism that regulates the gap between the floor and the brush. The brush is made of two components (rubber paddles and pile) with a V-shaped profile, which rakes the garbage into the container as efficiently as possible. Just below the receiving hole, there are 2 located for dispensing the collected waste to the self-cleaning station.
Software
The software is standard and fits all the manufacturer’s vacuum cleaners equipped with this function. To install, you need to use the QR code from the vacuum cleaner or paper instructions. After installation, go through the standard registration with authorization and connect the vacuum cleaner. To do this, you need to perform a series of simple actions with connecting to WiFi and indicating the QR code to the vacuum cleaner’s camera.
After or before connecting the vacuum cleaner, you can see the service instructions, view the most frequently asked questions, or download the electronic version of the paper connection instructions. In this sense, the manufacturer has approached quite well, and indeed the setting will be very simple, and if disputable situations arise, it will not take much time to solve it.
The next step is to check the relevance of the firmware and the application itself, and also in the future you can control the level of wear of consumables and after replacing it is definitely worth setting a new level.
When the basic settings have been made, you can start directly setting up the robot vacuum cleaner and sending it to cleaning the area. In this case, a map of the room will be created, therefore, during the first 3 arrivals, it is better not to interfere with the vacuum cleaner and to clean the floor of foreign objects as much as possible. Of course, you can later delete the card and create it again, for example, this will be needed when moving furniture in an apartment. After creating a map, you can set up virtual barriers, areas for spot cleaning or set a cleaning sequence in rooms.
While the vacuum cleaner is moving and cleaning, you can watch it on an interactive map and at the same time set additional power to it, regulate the water supply, set the cleaning time and create schedules. And if you delve into the settings, then there is an item for automatic unloading of garbage when the container is filled. This item can be activated when purchasing a garbage collection station.
All notifications about errors or completion of work can come to the smartphone desktop or in the application to the home page. Each notice can be read and if this is an error, then read the terms of its correction without leaving it.
If we compare the previous Yeedi 2 hybrid and the more advanced Yeedi vac max model with increased power and the Yeedi vac hybrid, then a number of improvements can be distinguished and at the same time the price will be slightly higher for a more progressive model.
conclusions
Before the first launch, my old man ILIFE A80 Plus cleaned the apartment with a full cleaning cycle. After that, the Yeedi vac hybrid was launched to build the map. During this time, he drove around the apartment 3 times and judging by the collected garbage, it can be concluded that it is time to change the old man. Quite large debris got into the container, which simply did not fit into the inlet of another vacuum cleaner, and this is a piece of plastic 12 * 7 * 8mm in size. The container also contained a lot of debris, dust and hair that was not removed before it.
The Yeedi vac hybrid vacuum cleaner is a bright representative of smart indoor cleaning technology, and a station for collecting dust from the main container will become a pleasant addition. This will extend the cleaning time and you will pay less attention to it. The vacuum cleaner adequately recognizes obstacles, bypasses them and creates a believable map with the ability to edit and set cleaning places and restricted areas.
